AR3000

AR3000a

AR5000

AR8000

AR8200

AR8600

IC-R10	IC-R20	IC PCR-100	IC PCR-1000	IC PCR-1500	IC-R1500
IC PCR-2500	IC-R2500	IC-R7000	IC-R7100	IC-R8500
Other CI-V compatible receivers (see Icom note)

Pro-2005 (with OptoScan456 board)	Pro-2006 (with OptoScan456 board)
Pro-2035 (with OptoScan535 board)

UBCT-8	UBCT-9	BCT15	USC230	UBC245XLT	BC246T
BR330T	BCD396T	UBC780XLT	UBC785XLT	UBC800XLT	BC895XLT
BC898T	BCD996T	UBC3300XLT	UBC3500XLT

FT-817	FT-847	FT-857	VR-5000	FRG-9600
Other CAT interface compatible Yaesu radios

Radios which are driven by the Icom CI-V protocol have a 'radio address'.
Just enter the appropriate CI-V address (in hex) for the particular radio in the Settings window and your radio should work with TrunkView!

PCR-100 / PCR-1000 / (PC)R-1500 / (PC)R-2500 users only have to check the 'PCR model' box.

• R1500
  Connect and determine the COM port being used by the R1500 (need only be done the first time).
  Thereafter do NOT use VFO or PC Mode (TrunkView will control the radio), exit the control panel and leave R1500 powered ON and connected to PC.
  Connect Audio lead from Ext SP to Line in/Microphone socket of PC.
  
  
• Windows
  Go to Control Panel->System->Hardware->Device manager->Ports and find the COM port installed by the 'USB to UART bridge controller'. (COM port used by the R1500)
  Open the Properties of this COM port, check Port settings and select 38400 as baudrate. (default will be 9600).
  
  
• TrunkView
  Open the Settings window.
  Set Sound Device to your PC's sound card.
  Go to RS232 and select the previously edited COM port, baudrate 38400, select Radio type Icom and tick 'PCR model'.

Uniden radios organize memory channels in two different ways:

1. the traditional banks, with a fixed number of channels per bank.
2. the recent radios have 'Dynamic Allocated Channel' memory. This means that all channels belong to a pool, and when a channel is needed, it is allocated to the group where it is needed.

Users of a traditional radio have to select a memory channel for the frequency manipulations. (Default: channel 500).
These types include: UBC245XLT, UBC780XLT, UBC785XLT, BC895XLT, BC898T, UBC3300XLT

If you have a radio with Dynamic channels, you only have to tick the 'Dynamic Memory' box.
These types include: BCT15, USC230, BC246T, BR330T, BCD396T, UBC800XLT, BCD996T, UBC3500XLT.



Press E key for 2 seconds.
If REMOTE mode is selected, the 'RMT' icon appears.

Change transfer speed:

• 1. Press MENU.
• 2. Press or to select SYSTEM DATA and then press E.
• 3. Press or to select PC CONTROL and then press E.
• 4. To change the transfer speed, press or . Then press E.
• 5. Press MENU, and press MENU again.

The OptoScan456/535 communication board is a CI-V compatible board with default address 80 (hex).
To use it, select Icom and enter CI-V address 80.
Radio addresses 80 to 8F are reserved for the OptoScan456/535.



If your radio is not listed, but seems to be compatible with TrunkView, just drop an e-mail and it will be added.